oktokopter
Junior Member

My guess is that the firmware wasn't properly uploaded at Rangevideo. Because this only happened on brand new OSDs.

Rochoa, como no puedo adjuntar fotos en los privados te respondo aquí. Si soldar el cable que te sugiero no funcionó entonces suelda este otro cable...

Es normal que falle la verificación. Esto se debe a la protección del firmware contra copias. Si grabas correctamente el firmware que se adapte a la...

This is weird, looks like it has lose the main board firmware. Seems to need a reflash of the main board. If you have the programmer check here:...

I still have the Queen bee(lucky me) However did not have time to flew it again. I already did flew on cumulus flight with another of my flying...

Que esten unidas las soldaduras del jumper en disable no es ningún problema, en realidad el jumper en esa posición no cumple ninguna función. Ese OSD...

Los códigos de desbloqueo deben manejarse via correo privado tal como especifico en las instrucciones, esto para no contaminar los hilos del forum.

Yes, I agree Vova should had put the warning. When you sell an all in one package you risk inexperienced people to buy it. But I have experienced...

Your interpretation is correct, with main battery jumper enabled RVOSD will select the highest voltage source to power itself, the camera and the...

The problem is, Rangevideo didn't design a prop neither the motor or the ESC. They just put everything together to make it easier for you. All...

This is why people use to put prop stoppers when using folding propellers on pusher motors(some just make sure the screws are tight enough). I wonder...

I did erased it, I do manage the forum, but there is very little I can do about orders. That has to be handled via support@rangevideo.com and they...

Like Ommadawn says, is very hard to get the current sensor to fail.

De que OSD estamos hablando? Espero sinceramente que no sea el mismo que ya tratamos mas arriba, esta sería la quinta clave que pides para el mismo y...

Works fine on my PC machine, Windows7 64 and latest Mozilla firefox.

"Rx not detected" significa que el OSD no ha detectado señal desde el Rx al inicio. O que el Rx estaba mandando señal de failsafe desde el...

Check again the Rx to OSD connections. Make sure elevator out goes to RVOSD elevator in and Aileron out goes to aileron in. Have seem this problem...

Servo directions should be properly set after you run the wizard... If you do it properly.

The only thing you have to try is here: http://www.rangevideo.com/forum/showthread.php?1530-RVOSD-G5-instructions-%28work-in-progress-%29 Make...

Vova told me that he found a baro damaged on one of them, the others had a damaged inductor. Hard to know how this happened.

I recommend you to use a PAL setup if your camera and monitor/goggles can handle it. OSD looks much better and there is better resolution. It will...

It will display properly when the plane is moving. Basically GPS heading depends on having enough speed in order to calculate the direction vector.

If the battery were 100% efficient you could have to put the same amps you put out. On the real world batteries are less efficiency, some energy is...

Part is this: http://www.digikey.com/product-detail/en/744066150/732-1077-2-ND/1638482?cur=USD About the cause of the crash... I think it was BEC...

You better change the servo buffer. It is cheap and does not work to take the risk.

All I can say is that RVOSD software does not crash. I programmed it on assembly language, thus there is a very close control of all processes....

You can't see anything wrong on it, but trust me, the problem is the cable. To be more precise, the problem is where the connector pins are clamped...

El problema puede ser que este firmware lo hice con un decodificador distinto. Prueba: GJ16BL

...tienes que poner el "call sign" a ON...

Your GPS cable or connectors are damaged, need to replace the cable.